ProgramMaster Logo
Conference Tools for 2019 TMS Annual Meeting & Exhibition
Register as a New User
Submit An Abstract
Propose A Symposium
Presenter/Author Tools
Organizer/Editor Tools
About this Symposium
Meeting 2019 TMS Annual Meeting & Exhibition
Symposium General Poster Session
Organizer(s) TMS Administration
Scope Note: This symposium is no longer accepting manuscript submissions for the Supplemental Conference Proceedings.
Abstracts Due 12/17/2018
Proceedings Plan Planned: Supplemental Proceedings volume

H-10: CFD-simulation of Siphone for Primary Aluminum Production
H-11: Control of TiC Particle Size in Combustion Synthesis Method for Reinforcement Particle
H-12: Corrosion Resistance of Hot Dipping Al-Zn-Si and Zn-Al-Mg-Si Alloy Coating
H-13: Creation of Mechanical Behaviour Diagrams of Twin Roll Cast Aluminum Flat Products Depending on Different Thermomechanical Processes
H-14: The Role of Scientific Publishers in Addressing Gender Disparity in Academic Publishing
H-15: Degradation of Organic Pollutant by Advanced Oxidation using the Fenton System Fe (II) / H2O2
H-16: Determination of Mechanical Properties of Boron Oxide Particle Reinforced Aluminum Alloy Matrix Composites
H-17: Development of the Sub-frame with Magnesium Alloy through the High-pressure Die-cast Process
H-18: Effect of Bias Voltage on Structure, Morphology and Hardness of ZrN Coating Deposited by Reactive Magnetron Sputtering
H-19: Effect of Decarbonization Annealing Times on Recrystallization Microstructure, Texture and Magnetic Properties of Nb-containing Grain-oriented Silicon Steel
H-20: Effect of Heat Treatment Parameters on Hardness and Microstructure of AISI 4140 and AISI 4150 Steels
H-21: Encapsulation of Gold Nanorods with Porphyrins for the Potential Treatment of Cancer and Bacterial Diseases
H-22: Evolution Behavior of Thermally Formed δ-ferrite in Modified 9Cr-1Mo Steel Weld Zone
H-23: Experimental Investigation of AA6061 Composites Reinforced With Fly Ash Fabricated By Friction Stir Processing
H-24: Fabrication and Mechanical Property Analysis of Nano-sphere Ti-Zr-Ni Quasicrystal
H-25: High Entropy Alloy Coatings for Erosion Resistance - A Review
H-26: Joining of Titanium and Stainless Steel Alloys via the Application of Refractory Metal Interlayers
H-27: Mechanical Property Characterization of Carbon Fiber Reinforced 6063 Alloy
H-28: Microstructure and Mechanical Properties of Beryllium-copper Alloy Plate Modified by Friction Stir Processing
H-29: Molecular Dynamics Simulations of Carbon Fibers Reinforced Within Polyethylene used to Quantify Decohesion of the Interfacial Region
H-30: Molten Salt Electrolytic Extraction of Dysprosium using NdFeB Magnet Scraps
H-31: Morphology and Mechanical Properties of Bagasse Nano Particles Reinforced Epoxy Composites
H-32: New Tool for Friction Stir Processing
H-33: Performance of Low Cost 3D Printed Pylon in Lower Limb Prosthetic Device
H-34: Phase-field Modeling of Metal Corrosion with Passive Film Formation in Electrolyte
H-35: Production of Sr Master Alloy by Pyrometallurgical and its Modification Capability
H-36: Research on Influence of Inclusion Size for IGF Inducing in Different Grain Size for Ti-Mg Shipbuilding Steel
H-37: Sand Casting Of Ze41 Mg Alloy
H-38: Sequential Leaching Characteristics of Chromium in AOD Slag-based Cementitious Materials
H-39: Strengthening Mechanisms Contribution of Formation of UFG Low C Microalloyed Steel and Structure Properties Correlation
H-40: Study on the Reaction Behavior of Hydrochloric Acid Containing Titanium Blast Furnace Slag
H-41: Study on Ultrasonic-assisted Metal 3D printing (UAM3P) for Making Alloys Printable without Defects
H-42: The Creep-fatigue Behavior of a Directionally Solidified Ni-based Superalloy DZ445 at 900 C with High Strain Range
H-43: The Edge Dislocation Climbing Mechanism for He Bubble Growth in W
H-44: The Effect of Electromagnetic Stirring on the Continuous Casting of Hypereutectic Al-Si Alloy Billets
H-45: The Effect of Sr Modification on Mechanical Properties and Corrosion Behavior of A360 alloy
H-46: Thermodynamic and Kinetic Analysis of Inhomogeneous Distribution of Solute on Precipitations in as Cast Nb-V-Ti Microalloyed Steel
H-47: Thermoelectric Properties of Amorphous Ti50Cu28Ni15Sn7-dispersed Bi0.4Sb1.6Te3 Fabricated by Mechanical Alloying and Vacuum Hot Pressing
H-48: Tunable Thermal Expansion Behavior in TbCo2 Based Alloys
H-49: Understanding Tip Material Selection Impact on High Temperature Nanoindentation
H-50: Utilization of Primary Steelmaking Slag as a Medium for Remediation of Arsenic Contaminated Groundwater
H-51: ZrO2 Doping Effects on the Mechanical and Structural Properties of Nanostructured Forsterite
H-52: Microstructural Characterization of Co-sputtered Cu-Ta Alloys as a Function of Processing Conditions
H-53: Heterogeneous Structure Hypereutectic Al- 20 wt.%Si by Laser Surface Remelting
H-54: Deformation Mechanisms of Crystalline Silicon Nitride Nanomembranes
H-55: Fracture of Adhesively Bonded Joints between Dissimilar Substrates under Shear: Modelling versus Experiment
H-56: Limits on Transformation Strains for Non-negative Dissipation
H-6: A Study on the Mechanical Properties of Glass Fiber-Epoxy Vinylester Composite with Pultrusion Process depends on Exposure time in Salt Spray Corrosion Environment
H-7: Appling Nanotechnology to Seperation of Fluride Gas with Oxygen by Carbon Nano Tube (Monte Carlo Simulatino)
H-8: Barrierless Cu-alloy Seed Integration for Improved Reliability in Solder Bump Flip Chip Applications
H-9: Rapid Solidification of Impulse Atomized Al-Si-Sc

Questions about ProgramMaster? Contact