ProgramMaster Logo
Conference Tools for 2016 TMS Annual Meeting & Exhibition
Register as a New User
Submit An Abstract
Propose A Symposium
Presenter/Author Tools
Organizer/Editor Tools
About this Symposium
Meeting 2016 TMS Annual Meeting & Exhibition
Symposium Material Behavior Characterization via Multi-Directional Deformation of Sheet Metal
Sponsorship TMS Materials Processing and Manufacturing Division
TMS: Shaping and Forming Committee
Organizer(s) John Carsley, General Motors Research & Development
Daniel R. Coughlin, Los Alamos National Laboratory
Myoung-Gyu Lee, Korea University
Youngung Jeong, National Institute of Standards and Technology
Piyush Upadhyay, Pacific Northwest National Laboratory
Scope Engineering sheet metals are customarily characterized by simple mechanical tests in order to meet mechanical properties given in OEM specifications. A set of uniaxial tension tests suffice to provide various standardized properties such as yield strength, ultimate tensile strength, strain hardening coefficient, Lankford coefficients, strain rate sensitivity and forming limits. However, when OEMs stamp a blank sheet to shape their final products, the materials experience quite complicated histories of straining paths that may significantly differ from behavior that is characterized by conventional mechanical tests. For example, sheet metals usually experience much higher strain rates, which may lead to phase transitions in the case of multiphase advanced high strength steels. Additionally, the amount of strain during a stamping process can far exceed what is typically obtained by the standard uniaxial tension test. Critical areas of a stamping often experience changes in the strain path.

The advanced constitutive models of today require material parameters obtained under multiaxial and complex loading conditions. Over the past decades, the sheet metal forming community has observed that such advanced constitutive models improve the predictive accuracy on formability and springback. However, in order to successfully train the models, unconventional experimental methods are often required. Here a list of notable experimental methods is given: 1) the cruciform test was designed to strain sheet metals in various stress ratios; 2) The tension-compression test was designed to provide a deformation history representing the bending and unbending of sheets during stamping; 3) The hydraulic bulge test is a widely spread method to obtain hardening curves to large levels of plastic strain, which standard uniaxial tests cannot provide; 4) Combination of non-coaxial loadings can provide various stress states, to which the phase transition is sensitive; 5) An experimental setup consisting of multiple steps with various pre-strainings is also practiced in order to observe constitutive behaviors under complex histories of deformation that may occur in typical industrial stamping processes; 6) High speed tests can subject the materials to a rate of speed similar to what is actually observed during the stamping process.

The objective of this symposium is to explore numerous advances in experimental testing and computational methods used for material characterization, constitutive modeling, and analyses pertaining to sheet metal deformation in multiple directions along multiple axes or with changing strain path conditions. Potential participants are encouraged to submit abstracts on research of material behavior related to microstructure based on multiple directional deformation including but not limited to: improvements and new methods of mechanical property measurement; characterization of phase transformations and deformation mechanisms in multiphase microstructures during forming; theory and modeling related to the mechanical properties; deformation simulations, forming processes, friction and springback; multi-directional mechanical testing and advanced strain/stress measurements; integration of scientific knowledge with manufacturing practices; and development of accurate constitutive relationships.
Abstracts Due 07/15/2015
Proceedings Plan Planned: A print-only volume

A Novel In-situ Planar Biaxial Experiment
Advanced Cruciform Testing at the NIST Center for Automotive Lightweighting
An Experimental and Microstructural Investigation of Biaxial Bauschinger Effects in Sheet Metals
An Experimentally Validated, Microstructure Based Model for Forming of Low-symmetry Alpha-uranium
Biaxial Loading of Anisotropic Al-6022-T4 Sheets Using Cruciform Specimens
Determination of Bending Limit Curves for Aluminium Alloy AA6014-T4: An Experimental Approach
Dilational Response of Voided Polycrystals
Effect of Complex Strain Paths on Microstructure Evolution Studied by In-situ Neutron Diffraction
Evalution of Formability in Aluminum Alloys across Strain Rates Using Digital Image Correlation Technique
Hardening Behavior of 316L SS Subject to Biaxial Strain Path Change: Multiscale Modeling for Guiding Experiments
Inflation of Stainless Steel 304L Microtubes under Axial Tension and Internal Pressure to Assess the Plastic Anisotropy
Modeling Anisotropic Hardening and Nonlinear Elasticity under Loading Path Change
Multi-scale Analysis of Springback in Microforming of Thin Nickel Sheets
On the Non-proportional Deformation of Sheet Steel Using In-situ Diffraction and Modelling Methods
Onset of Plasticity via Relaxation Analysis (OPRA)
Optimization of Biaxial Tensile Test Specimen Design
Predicting Cyclic Deformation of AA6022-T4 and DP590 Using Polycrystal Plasticity
Sensitivity Analysis of the Bauschinger Behavior on Bending Springback for Prestrained Sheets
The Influence of Deformation Mechanisms on Forming of Commercially Pure Titanium Sheets

Questions about ProgramMaster? Contact