ProgramMaster Logo
Conference Tools for 2018 TMS Annual Meeting & Exhibition
Login
Register as a New User
Help
Submit An Abstract
Propose A Symposium
Presenter/Author Tools
Organizer/Editor Tools
About this Symposium
Meeting 2018 TMS Annual Meeting & Exhibition
Symposium General Poster Session
Sponsorship
Organizer(s) TMS Administration
Scope
Abstracts Due 07/16/2017
Proceedings Plan Planned: Supplemental Proceedings volume
PRESENTATIONS APPROVED FOR THIS SYMPOSIUM INCLUDE

O-10: Control of Prior Particle Boundary Formation in Hot Iso-statically Pressed Nickel-based Superalloys
O-12: Development of a Cu-alloy Seed Buffer Layer for Solder Bump Flip Chip Application
O-13: Direct Metal Write of Aluminum Alloys with Enhanced Surface Stability
O-14: Effect of Colony Size on Tensile Fracture Behavior in Lamellar and Bi-lamellar Microstructures of Ti-6Al-4V Alloys
O-16: Effect of Surface Treatment of Copper and its Alloys on the Antimicrobial Properties of the Surfaces
O-17: Effect of Tin Content on Microstructure and Mechanical Properties of High Carbon Steels
O-18: Enhancement of Thermoelectric Properties of Mechanically Alloyed Bi0.4Sb1.6Te3 Nanocomposites by Addition of γ-Al2O3 Particles
O-19: Evaluation of the Formation of Intermetallic Compounds in Aluminum-steel Joints According to the Joining Method
O-20: Fabrication of Nb-Si-B Alloys by Solidification Process and SPS Process
O-21: Fatigue Strength Characteristics of Tandem Gas Metal Arc Welding in Automotive Chassis Parts
O-22: Functional Requirements for Expected Properties of Antimicrobial Touch Surfaces Based on Copper and its Alloys
O-23: Gold Nanoparticles on Multilayer Graphene Sheets for Surface Enhanced Raman Spectroscopy of Glucose
O-25: High Strain Rate Deformation of Automobile Grade Steels
O-26: Highly Ordered Nickel Cobalt Sulfide Nanowires Grown Woven Kevlar Fiber Composites
O-28: Hot Isostatic Pressing and Laser Additive Manufacturing of Niobium-Based Refractory Powders
O-30: In-process Microstructure Tuning in Solid-state Ambient Condition Metal Additive Manufacturing
O-31: In-situ TEM Micocantilever Measurements of Al2O3- SmAlO3 Interfacial Toughness
O-32: Indentification of Gases Evolved during Firing Processes of Oxide Ceramics by Means of Thermal Analysis Coupled to Mass Spectrometry
O-33: Influence of Cold Spray on the Microstructure and Residual Stress of Resistance Spot Welded Steel-Mg
O-34:Investigation of Adiabatic Heat Rise and its Effect on Flow Stresses and Microstructural Changes during High Strain Rate Deformation of Ti6Al4V Alloy
O-35: Investigation of Susceptibility of A533B SAteel to Temper Embrittlement
O-38: Microstructural Influence on Cracking Resistance of Ti-6Al-4V ELI Alloy at Sour Environment
O-39: Microstructure and Mechanical Properties of Al-Mg Based Alloy Sheets Processed by Cold Rolling
O-3: Additive Manufacturing of Epoxy Resin Matrix Reinforced with Magnetic Particles
O-40: Nanostructured Steel Susceptibility to Sulfide Stress Cracking
O-41: Optimisation of Celestite Leaching by Using Respond Surface Methodology
O-42: Real Time Estimation of Resistance Spot Weld Quality by Using Artificial Neural Network
O-44: Resistance Spot Weldability of 980MPa Grade Steel with 24% Elongation
O-45: Rheological and Fatigue Resistance of High Strength and High Conductivity Cu-Ag Alloys Wires
O-46: Robust Accumulation of Research Foundational Knowledge in the Thermo Material Sciences
O-47: Scoping the Response of Materials under Fission and Fusion Conditions via Inventory Simulations
O-48: Study of Temperature Dependent Elastic Properties of SnSe Using Resonant Ultrasound Spectroscopy
O-4: Admixture Optimization in Concrete Using Superplasticizers
O-50: Study on the High-frequency Heat Treatment Process for the Dual Phase High-pressure Pipe Fabrication
O-51: Superelastic Scaffolds Prepared by Sintering of Metal Fibers for Biomedical Applications
O-52: Synthesis and Characterization of Novel Phosphonated and Sulfonated Poly(styrene-isobutylene-styrene) Membranes for Fuel Cell and Protective Clothing Applications
O-55: The Effect of Complexion Transitions on Single Grain Boundary Fracture Toughness of Alumina
O-56: The Effect of Cooling Rate on Microstructure and Physical Properties for Alloy 625 Casting
O-57: The Effect of Thermal Treatment on Microstructure and Mechanical Properties of Infiltrated TiB2-steel Composites
O-58: The Influence of Frequency on Ultrasonic Vibration-assisted Laser Atomization of TI-alloy
O-59: Effect of Trace Elements on Microstructure and Material Properties of an Aluminium Alloy
O-5: Analysis of Plastic Deformation in Ti-Zr-Ni Quasicrystals
O-60: Ultra-high Strength and High Conductivity Cu-Ag Alloys Wires Designed for the Construction of High Magnetic Fields Generators
O-61: Wear Behavior of Additive Manufactured Orthopedic Ceramics
O-62: Optimizing Microstructure, Strength and Ductility of Medium-Entropy NiCoCr and Ni-Base Superalloy IN740H
O-63: Tuning the Luminescence Properties of Eu3+ Doped SiO2 Glasses by Additions of Amino Acids
O-6: Ball Milling of Machine Chips as an Alternative Feedstock for Additive Manufacturing
O-7: Bayesian Inference Based Uncertainty Quantification and Propagation Analysis of a Polycrystal Plasticity Finite Element Model Used for High Cycle Fatigue Analysis of Ti-6Al-4V
O-8: Characterization Study of Binder-jet Printed of TiC-Aluminum Cermet


Questions about ProgramMaster? Contact programming@programmaster.org